View SMA6820MH_8406062.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

sanken electric co., ltd. http://www.sanken-ele.co.jp/en/ description the SMA6820MH inverter power module (ipm) series provides a robust, highly-integrated solution for optimally controlling 3-phase motor power inverter systems and variable speed control systems used in energy-conserving designs to drive motors of residential and commercial appliances. these ics take 230 vac input voltage, and up to 2.5 a (continuous) output current. they can withstand voltages of up to 500 v (mosfet breakdown voltage). the SMA6820MH power package includes an ic with all of the necessary power elements (six mosfets) and pre-driver ics (two) needed to configure the main circuit of an inverter. this enables the main circuit of the inverter to be configured with fewer external components than traditional designs. applications include residential white goods (home applications) and commercial appliance motor control: ? air conditioner fan ? small ventilation fan ? dishwasher pump features and benefits ? built-in pre-drive ic and 3 bootstrap diodes as a high-side drive power supply ? cmos compatible input (3.3 to 5 v) ? high-side gate driver using bootstrap circuit or floating power supply ? one pin for 7.5 v regulator output ? built-in protection circuit for controlling power supply voltage drop ? built-in overheat detection circuit (td) ? output of fault signal during operation of protection circuit ? output current 1.5, 2, or 2.5 a ? small sip (sma 24-pin) high voltage 3-phase motor drivers figure 1. driver block diagrams. leadform 2452 packages: power sip not to scale leadform 2451 functional block diagram high side level shift driver low side driver uvlo uvlo uvlo uvlo input logic input logic uvlo thermal detect 7.5v reg. vd vcc1 vb 1 vb 2 vb3 vbb 1 vbb 2 u v w1 w2 ls1 ls2 fo com2 lin3 lin2 lin1 vreg vcc2 com1 hin3 hin2 hin1 SMA6820MH series SMA6820MH-ds
2 sanken electric co., ltd. high voltage 3-phase motor drivers SMA6820MH series all performance characteristics given are typical values for circuit or system baseline design only and are at the nominal operating voltage and an ambient temperature, t a , of 25c, unless oth er wise stated. recommended operating conditions characteristic symbol remarks min. typ. max. units main supply voltage v bb sma6821mh between vbb and ls ? 150 200 v sma6822mh ? 300 400 v sma6823mh ? 300 400 v logic supply voltage v cc between vcc and com 13.5 ? 16.5 v dead time t dead 1.5 ? ? s minimum input pulse width t inmin 0.5 ? ? s selection guide part number mosfet breakdown voltage, v dss (min) (v) output current continuous, i o (max) (a) pulsed, i op (max) (a) sma6821mh 250 2 3 sma6822mh 500 1.5 2.25 sma6823mh 500 2.5 3.75 absolute maximum ratings , valid at t a = 25c characteristic symbol remarks rating unit mosfet breakdown voltage v dss sma6821mh v cc = 15 v, i d = 100 a, v in = 0 v 250 v sma6822mh 500 v sma6823mh 500 v logic supply voltage v cc between vcc and com 20 v bootstrap voltage v bs between vb and hs (u,v, and w phases) 20 v output current, continuous i o sma6821mh t c = 25c 2a sma6822mh 1.5 a sma6823mh 2.5 a output current, pulsed i op sma6821mh pw 100 s, duty cycle = 1% 3a sma6822mh 2.25 a sma6823mh 3.75 a output current for regulator i reg 35 ma input voltage v in hinx and linx pins ?0.5 to 7 v allowable power dissipation p d t c = 25c 28 w thermal resistance (junction to case) r jc all elements operating 4.46 c/w thermal resistance (junction to air) r ja all elements operating 31.25 c/w case operating temperature t cop ?20 to 100 c junction temperature (mosfet) t j 150 c storage temperature t stg ?40 to 150 c SMA6820MH-ds
3 sanken electric co., ltd. high voltage 3-phase motor drivers SMA6820MH series vcc2 lin1 vcc1 hin1 com1 vb1 ho3 hs3 lin2 lin3 fo com2 lo1 lo2 lo3 m cont roller 15v hvic SMA6820MH lvic hin2 hin3 vb2 vb3 ho2 ho1 hs1 hs2 10 1 3 4 5 9 6 7 8 24 13 12 14 11 17 16 15 23 22 19 18 20 21 vreg 2 note: ? all of the input pins are connected to gnd with internal pull-down resistors rated at 100 k , however, an external pull-down resistor may be required to secure stable condition of the inputs if high impedance conditions are applied to them. ? the external electrolytic capacitors should be placed as close to the ic as possible, in order to avoid malfunctions from external noise interference. put a ceramic capacitor in parallel with the electrolytic capacitor if further reduction of noise susceptibility is necessary. typical application diagram SMA6820MH-ds
4 sanken electric co., ltd. high voltage 3-phase motor drivers SMA6820MH series electrical characteristics, valid at t a =25c, unless otherwise noted characteristics symbol conditions min typ max units logic supply voltage v cc between vcc and com 13.5 15 16.5 v logic supply current i cc v cc = 15 v, i reg = 0 a ? 4 6 ma input voltage v ih v cc = 15 v, output on ? 2.0 2.5 v v il v cc = 15 v, output off 1.0 1.5 ? v input voltage hysteresis v ihys v cc = 15 v ? 0.5 ? v input current i ih high side, v cc = 15 v, v in = 5 v ? 50 100 a i il low side, v cc = 15 v, v in = 0 v ? ? 2 a undervoltage lock out v uvhl high side, between vbx and u, v, or w 9.0 10.0 11.0 v v uvhh 9.5 10.5 11.5 v v uvhhys high side, hysteresis ? 0.5 ? v v uvll low side, between vcc2 and com2 10.0 11.0 12.0 v v uvlh 10.5 11.5 12.5 v v uvlhys low side, hysteresis ? 0.5 ? v fo terminal output voltage v fol v cc = 15 v 0 ? 1.0 v v foh 4.0 ? 5.5 v overtemperature detectionthreshold temperature (activation and deactivation) t dh v cc = 15 v, no heatsink 135 150 165 c t dl 105 120 135 c t dhys ?30?c output voltage for regulator v reg i reg = 35 ma 6.75 7.5 8.25 v bootstrap diode leakage current i lbd sma6821mh v r = 250 v ? ? 10 a sma6822mh v r = 500 v ? ? 10 a sma6823mh v r = 500 v ? ? 10 a bootstrap diode forward voltage v fbd i f = 0.15 a ? 1.1 1.3 v bootstrap diode series resistor r bd 17.6 22 26.4 mosfet breakdown voltage v dss sma6821mh v cc = 15 v, i d = 100 a, v in = 0 v 250 ? ? v sma6822mh 500 ? ? v sma6823mh 500 ? ? v mosfet leakage current i dss sma6821mh v cc = 15 v, v ds = 250 v, v in = 0 v ? ? 100 a sma6822mh v cc = 15 v, v ds = 500 v, v in = 0 v ? ? 100 a sma6823mh v cc = 15 v, v ds = 500 v, v in = 0 v ? ? 100 a mosfet on state resistance r ds(on) sma6821mh v cc = 15 v, i d = 1.0 a, v in = 5 v ? 1.25 1.5 sma6822mh v cc = 15 v, i d = 0.75 a, v in = 5 v ? 3.6 4 sma6823mh v cc = 15 v, i d = 1.25 a, v in = 5 v ? 2.0 2.4 mosfet diode forward voltage v sd sma6821mh v cc = 15 v, i sd = 1.0 a, v in = 0 v ? 1.1 1.5 v sma6822mh v cc = 15 v, i sd = 0.75 a, v in = 0 v ? 1.1 1.5 v sma6823mh v cc = 15 v, i sd = 1.25 a, v in = 0 v ? 1.1 1.5 v SMA6820MH-ds
5 sanken electric co., ltd. high voltage 3-phase motor drivers SMA6820MH series sma6821mh switching characteristics, valid at t a =25c, unless otherwise noted characteristics symbol conditions min typ max units switching time, high side t dh(on) v bb = 150 v, v cc = 15 v, i d = 1 a, 0 v v in 5 v ? 430 ? ns t rh ?55?ns t dh(off) ? 355 ? ns t fh ?20?ns switching time, low side t dl(on) v bb = 150 v, v cc = 15 v, i d = 1 a, 0 v v in 5 v ? 405 ? ns t rl ?60?ns t dl(off) ? 395 ? ns t fl ?20?ns sma6822mh switching characteristics, valid at t a =25c, unless otherwise noted characteristics symbol conditions min typ max units switching time, high side t dh(on) v bb = 300 v, v cc = 15 v, i d = 0.75 a, 0 v v in 5 v ? 485 ? ns t rh ?85?ns t dh(off) ? 420 ? ns t fh ?30?ns switching time, low side t dl(on) v bb = 300 v, v cc = 15 v, i d = 0.75 a, 0 v v in 5 v ? 520 ? ns t rl ? 100 ? ns t dl(off) ? 485 ? ns t fl ?25?ns sma6823mh switching characteristics, valid at t a =25c, unless otherwise noted characteristics symbol conditions min typ max units switching time, high side t dh(on) v bb = 300 v, v cc = 15 v, i d = 1.25 a, 0 v v in 5 v ? 665 ? ns t rh ? 145 ? ns t dh(off) ? 545 ? ns t fh ?40?ns switching time, low side t dl(on) v bb = 300 v, v cc = 15 v, i d = 1.25 a, 0 v v in 5 v ? 720 ? ns t rl ? 175 ? ns t dl(off) ? 605 ? ns t fl ?45?ns SMA6820MH-ds
6 sanken electric co., ltd. high voltage 3-phase motor drivers SMA6820MH series hin vb-hs ho v uvhh v uvhl uvlo release lin vcc lo v uvhh fo v uvhl t j t dh t dl uvlo release low side driver input/output timing diagrams after uvlo is released, ic operation is started by the first rising edge of input high side driver input/output timing diagrams SMA6820MH-ds
7 sanken electric co., ltd. high voltage 3-phase motor drivers SMA6820MH series terminal list table number name function 1 vb1 high side bootstrap terminal (u phase) 2 vb2 high side bootstrap terminal (v phase) 3 vd bootstrap diode anode terminal 4 vb3 high side bootstrap terminal (w phase) 5 vcc1 high side logic supply voltage 6 com1 high side logic gnd terminal 7 hin3 high side input terminal (w phase) 8 hin2 high side input terminal (v phase) 9 hin1 high side input terminal (u phase) 10 vbb1 main supply voltage 1 (connect to vbb2 externally) 11 vbb2 main supply voltage 2 (connect to vbb1 externally) 12 w1 output of w phase (connect to w2 externally) 13 v output of v phase 14 w2 output of w phase (connect to w1 externally) 15 ls2 low side source terminal (connect to ls1 externally) 16 vreg internal regulator output terminal 17 ls1 low side source terminal (connect to ls2 externally) 18 lin3 low side input terminal (w phase) 19 lin2 low side input terminal (v phase) 20 lin1 low side input terminal (u phase) 21 com2 low side gnd terminal 22 fo overtemperature and low-side uvlo fault-signal output 23 vcc2 low side logic supply voltage 24 u output of u phase pin-out diagrams 1357911131517192123 2 4 6 8 10 12 14 16 18 20 22 24 chamfer side leadform 2452 leadform 2451 chamfer on opposite side 1357911131517192123 2 4 6 8 10 12 14 16 18 20 22 24 SMA6820MH-ds
8 sanken electric co., ltd. high voltage 3-phase motor drivers SMA6820MH series 1.27 0.1 24681012141618202224 1 3 5 7 9 11 13 15 17 19 21 23 4 0.2 10.2 0.2 seating plane r1 ref 4.4 ref 2.2 0.7 bsc 2.2 0.7 bsc 3 0.5 bsc 1.2 0.1 bsc a c c measured at pin exit from case maximum dambar protrusion 0.6 +0.15 ? 0.05 0.55 +0.2 ? 0.1 0.7 +0.15 ? 0.05 0 to 0.4 0 to 0.4 a 1.27 0.6 b b measured at pin tips 31 0.2 31.3 0.2 gate protrusion on either side view a 2x gate protrusion 2x exposed tie bar leadform: 2451 terminal core material: cu terminal plating: ni and solder (sn 97.5%, ag 2.5%) plating case material: epoxy resin dimensions in millimeters branding area branding codes (exact appearance at manufacturer discretion): front branding area 1st line, lot: ymdd r where: y is the last digit of the year of manufacture m is the month ( 1 to 9, o, n, d ) dd is the date r is the sanken reference number 2nd line, type: sma682xmh back branding area 1st line, subtype: x where: x matches x in the type brand on front package outline drawing leadform 2451 dual rows, 24 alternating pins; pins bent 90 for horizontal case mounting; pin #1 in outer row leadframe plating pb-free. device composition complies with the rohs directive. SMA6820MH-ds
9 sanken electric co., ltd. high voltage 3-phase motor drivers SMA6820MH series leadform: 2452 terminal core material: cu terminal plating: ni recommended attachment: solder dip (sn-ag-cu) dimensions in millimeters branding area branding codes (exact appearance at manufacturer discretion): front branding area 1st line, lot: ymdd r where: y is the last digit of the year of manufacture m is the month ( 1 to 9, o, n, d ) dd is the date r is the sanken reference number 2nd line, type: sma682xmh back branding area 1st line, subtype: x where: x matches x in the type brand on front 31 0.2 31.3 0.2 1.27 0.5 0.6 +0.15 ? 0.05 0.5 +0.15 ? 0.05 9.5 +0.7 ? 0.5 10.2 0.2 a a measured at pin tips 2 4 6 8 10 12 14 16 18 20 22 24 1 3 5 7 9 11 13 15 17 19 21 23 4 0.2 r1 ref 4.5 ref 4.5 0.5 5 0.5 1.2 0.1 bsc view a deflection at pin bend 0.7 max 0.7 max view a 2x gate protrusion 2x exposed tie bar gate protrusion on either side package outline drawing leadform 2452 dual rows, 24 alternating pins; vertical case mounting; pin #1 opposite chamfer side leadframe plating pb-free. device composition complies with the rohs directive. SMA6820MH-ds
10 sanken electric co., ltd. high voltage 3-phase motor drivers SMA6820MH series because reliability can be affected adversely by improper storage environments and handling methods, please observe the following cautions. cautions for storage ? ensure that storage conditions comply with the standard temperature (5c to 35c) and the standard relative humidity (around 40 to 75%); avoid storage locations that experience extreme changes in temperature or humidity. ? avoid locations where dust or harmful gases are present and avoid direct sunlight. ? reinspect for rust on leads and solderability of products that have been stored for a long time. cautions for testing and handling when tests are carried out during inspection testing and other standard test periods, protect the products from power surges from the testing device, shorts between adjacent products, and shorts to the heatsink. remarks about using silicone grease with a heatsink ? when silicone grease is used in mounting this product on a heatsink, it shall be applied evenly and thinly. if more silicone grease than required is applied, it may produce stress. ? volatile-type silicone greases may permeate the product and produce cracks after long periods of time, resulting in reduced heat radiation effect, and possibly shortening the lifetime of the product. ? our recommended silicone greases for heat radiation purposes, which will not cause any adverse effect on the product life, are indicated below: type suppliers g746 shin-etsu chemical co., ltd. yg6260 momentive performance materials sc102 dow corning toray silicone co., ltd. soldering ? when soldering the products, please be sure to minimize the working time, within the following limits: 2605c 10 s 38010c 5 s ? soldering iron should be at a distance of at least 1.5 mm from the body of the products electrostatic discharge ? when handling the products, operator must be grounded. grounded wrist straps worn should have at least 1 m of resistance to ground to prevent shock hazard. ? workbenches where the products are handled should be grounded and be provided with conductive table and floor mats. ? when using measuring equipment such as a curve tracer, the equipment should be grounded. ? when soldering the products, the head of soldering irons or the solder bath must be grounded in other to prevent leak voltages generated by them from being applied to the products. ? the products should always be stored and transported in our shipping containers or conductive containers, or be wrapped in aluminum foil. SMA6820MH-ds
11 sanken electric co., ltd. high voltage 3-phase motor drivers SMA6820MH series ? the contents in this document are subject to changes, for improvement and other purposes, without notice. make sure that this is the latest revision of the document before use. ? application and operation examples described in this document are quoted for the sole purpose of reference for the use of the prod- ucts herein and sanken can assume no responsibility for any infringement of industrial property rights, intellectual property r ights or any other rights of sanken or any third party which may result from its use. ? although sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of se micon- ductor products at a certain rate is inevitable. users of sanken products are requested to take, at their own risk, preventativ e measures including safety design of the equipment or systems against any possible injury, death, fires or damages to the society due to device failure or malfunction. ? sanken products listed in this document are designed and intended for the use as components in general purpose electronic equ ip- ment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). when considering the use of sanken products in the applications where higher reliability is required (transportation equipment and its control systems, traffic signal control systems or equipment, fire/crime alarm systems, various safety devices, etc.), and whenever long life expectancy is required even in general purpose electronic equipment or apparatus, please contact your nearest sanken sales representative to discuss, prior to the use of the products herein. the use of sanken products without the written consent of sanken in the applications where extremely high reliability is requi red (aerospace equipment, nuclear power control systems, life support systems, etc.) is strictly prohibited. ? in the case that you use sanken products or design your products by using sanken products, the reliability largely depends on the degree of derating to be made to the rated values. derating may be interpreted as a case that an operation range is set by dera ting the load from each rated value or surge voltage or noise is considered for derating in order to assure or improve the reliability. in general, derating factors include electric stresses such as electric voltage, electric current, electric power etc., environmental stres ses such as ambient temperature, humidity etc. and thermal stress caused due to self-heating of semiconductor products. for these stress es, instantaneous values, maximum values and minimum values must be taken into consideration. in addition, it should be noted that since power devices or ic's including power devices have large self-heating value, the de gree of derating of junction temperature affects the reliability significantly. ? when using the products specified herein by either (i) combining other products or materials therewith or (ii) physically, ch emically or otherwise processing or treating the products, please duly consider all possible risks that may result from all such uses in advance and proceed therewith at your own responsibility. ? anti radioactive ray design is not considered for the products listed herein. ? sanken assumes no responsibility for any troubles, such as dropping products caused during transportation out of sanken's dis tribu- tion network. ? the contents in this document must not be transcribed or copied without sanken's written consent. SMA6820MH-ds

▲Up To Search▲

Price & Availability of SMA6820MH

	To Download SMA6820MH Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .